|
|
Loudspeaker Management
Fonksiyon:
Operation range 6, 12, 18, 32, 48dB/oct. slope; Butterworth,
Bessel, Linkwitz-Riley
Filters 32 parametric equalizers, 16 shelving equalizer
Low-Shelving equalizer, Hi-Shelving equalizer
Lo-Cut filter, Hi-Cut filter, All-Pass filter
Compressor / limiter 6 digital compressors / limiters
Delay 2master delays (0ms - 3000 ms)
6channel delays (0 ms 3000ms)
delay-increment 21 usec.
Data format 32-bit linear AD / DA conversion, 48-bit processing
Sampling rate 48 kHz
Inputs
2 x XLR IN, electronically balanced
2 x XLR OUT (Direct Out)
Input voltage (nominal) 1.55 V / + 6 dBu
Max. input voltage 24.5 V / + 30 dBu
Input impedance 20 kohms
Common mode rejection > 70 dB (1kHz)
AD-conversion 32-bit, Sigma-Delta, 128 times oversampling, linear phase
Outputs
6 x XLR OUT, electronically balanced
Output voltage (nominal) 1.55 V / + 6 dBu
Max. output voltage 8.7 V / + 21 dBu
Output impedance < 100 ohms
Min. load impedance 600 ohms
DA-conversion 32-bit, Sigma-Delta, 128 times oversampling
Frequency response 20 Hz - 20 kHz (- 0.5 dB)
S/N ratio 110 dB (typical)
Distortion < 0.01 %
PLA MX4000 Amplifier
Introduction:
MX Series amplifiers are designed for high operating efficiency and accurate sonic performance across the full audio bandwith, even under stressful conditions. In order to maintain quality assurance standards, all MX series amplifiers are built in MASS's state of the art manufacturing facility. Internal components are the finest available, and key sub-assemblies are pre tested before final assembly. Finally, each amplifier is burned in and throughly tested (using precision audio test equipment) before packing. In addition, all MX series amplifiers incorporate MASS exclusive TourClass protection features to safeguard both internal circuitry and connected loudspeakers. This proven combination of advanced design, quality construction, and comprehensive circuit protection is the guarantee of fail safe releability. You can depend on consistent, stable performance even when your MX series amplifier is subjected to punishing extremes in the most demanding fixed or mobile sound reinforcement applications.
Tour Class Protection:
Every model in the MX Series incorporates TourClass protection features.
ACL (Active Clip Limiting):
At the amplifiers full power limit, or clipping point, ACL will be activated. This is indicated by illumination of the Clip LED. The channel gain is automatically reduced, protecting the loudspeakers from potential damage from the high power, continous square waves that would otherwise be produced. ACL may be activated by uncontrolled feedback, oscillations, improper equipment gain settings, or an equipment malfunction upstream from the amplifier. Only steady or excessive cliping (not normal program transients) will trigger ACL. The circuit is virtually transparent in operation and full signal bandwith in maintained.
IGM Impedance Sensing:
IGM (Instantaneous Gain Modulation) is an innovative circuit that allows the maplifier to operate safely into loads as low as 2 ohms. When the amplifier sees a load that overstresses the output stage, the IGM circuit adjust the channel gain to a safe level. Like ACL, the IGM circuit is in audible in normal use. In addition, if extreme and sustained low impedance is encounteredi the amplifiers output relay will open.
ShortCircuit:
If an output is shorted (i.e., defective speakers or crossed speaker wires) the IGM and thermal circuits will automatically protect the amplifier. The IGM circuit senses the short circuit as an extremely stressfull load condition and attenuates the signal, protecting the channels output transistors from over current stress. If the short circuit remains, the load will be disconnected by the thermal protection circuitry (output relay opens).
SPECIFICATIONS MX 4000
1 kHz, 0.01% THD+N:
8ohm Stereo Power = 400W
4ohm Stereo Power = 600W
2ohm Stereo Power = 750W
8ohm Bridged Mono Power = 1200W
20Hz-20kHz, 0.1% THD+N:
8ohm Stereo Power = 350W
4ohm Stereo Power = 500W
2ohm Stereo Power = 600W
8ohm Bridged Mono Power = 1000W
Max RMS Output Voltage (each channel) = 73V
Max Peak Output Voltage = 103V
Frequency Response (+o/-0.3dB, 1W/8ohm) = 20Hz-20kHz, -3dB@135kHz
Power Bandwidth (rated power @ 4ohm,1%THD+N = 20Hz-20kHz,-1.1dB/+0dB
TourClass Protection = ACL,IMG, AutoRamp, Short Circuit, DC Voltage turn on/off transient, current inrush, sub/ultrasonic input
THD+N rated power 4ohm/1kHz = < 0.01%
SMPTE IMD (rated power. 8ohm.60Hz &7kHz = < 0.01%
Damping Factor (10-400Hz @ 8ohm = 400:1
Input CMRR (1 kHz) = > -60dB
Standart Voltage Gain (rated power @ 8ohm)‡ = 0.775V
Standart Input Sensitivity (rated power @ 8ohm)‡ = X68
Input Impedance (balanced/unbalanced) = > 20kohm/ >10kohm
Hum & Noise ('A' weighted, full power @ 4ohm) = -105 dB
Crosstalk ('A' weighted, full power @ 4ohm) = > -60 dB
Class = H
Input Connectors (per channel) = Female XLR (pin2+, configurable for pin3+) TRS (tip+)
Output Connectors (per channel) = 5-Way binding posts (2pair on CA18) or Speakon Connectors (market dependent)
Filter Storage = 68,000 µ F
Power Supply (factory configured) = 100V - 240V, 50-60Hz
Idle Current Draw (120V) = 1.6A
1/8 Power Curr.Draw (typical music cond., 120V/4ohm) = 6.0A
1/3 Power Curr.Draw (cont.music cond., 120V/4ohm) = 13.0A
Max Curr. Draw (continious music cond., 120V/4ohm) = 18.0A
Thermal Emissions (1/8 Power, 4ohm) = 2630 BTU/hr
Thermal Emissions (1/3 Power, 4ohm) = 3713 BTU/hr
Cooling = Two panel variable speed DC fans, filters detachable without tools
Controls = Front Panel: 2 attenuators, magnetic circuit breaker/power switch Rear Panel: signal ground lift & mode switches; CA18 XLR Polarity & input sens. Voltage Gain Switches
LED Indicators (per channel) = Clip/Limit Signal Temp/DC Active
Construction = Steel Chasis 16 Gauge Double Thickness in rear areas
Dimensions (height x width x depth to rear rack ears) = 3.5'' x 19'' x 18'' 89 x 483 x 457 mm
Gross Weight = 49 lbs 22.24kg
Net Weight = 44 lbs 19.97kg
Warranty = 3 Years
PLA MX6000 Amplifier
Introduction:
MX Series amplifiers are designed for high operating efficiency and accurate sonic performance across the full audio bandwith, even under stressful conditions. In order to maintain quality assurance standards, all MX series amplifiers are built in MASS's state of the art manufacturing facility. Internal components are the finest available, and key sub-assemblies are pre tested before final assembly. Finally, each amplifier is burned in and throughly tested (using precision audio test equipment) before packing. In addition, all MX series amplifiers incorporate MASS exclusive TourClass protection features to safeguard both internal circuitry and connected loudspeakers. This proven combination of advanced design, quality construction, and comprehensive circuit protection is the guarantee of fail safe releability. You can depend on consistent, stable performance even when your MX series amplifier is subjected to punishing extremes in the most demanding fixed or mobile sound reinforcement applications.
Tour Class Protection:
Every model in the MX Series incorporates TourClass protection features.
ACL (Active Clip Limiting):
At the amplifiers full power limit, or clipping point, ACL will be activated. This is indicated by illumination of the Clip LED. The channel gain is automatically reduced, protecting the loudspeakers from potential damage from the high power, continous square waves that would otherwise be produced. ACL may be activated by uncontrolled feedback, oscillations, improper equipment gain settings, or an equipment malfunction upstream from the amplifier. Only steady or excessive cliping (not normal program transients) will trigger ACL. The circuit is virtually transparent in operation and full signal bandwith in maintained.
IGM Impedance Sensing:
IGM (Instantaneous Gain Modulation) is an innovative circuit that allows the amplifier to operate safely into loads as low as 2 ohms. When the amplifier sees a load that overstresses the output stage, the IGM circuit adjust the channel gain to a safe level. Like ACL, the IGM circuit is in audible in normal use. In addition, if extreme and sustained low impedance is encounteredi the amplifiers output relay will open.
ShortCircuit:
If an output is shorted (i.e., defective speakers or crossed speaker wires) the IGM and thermal circuits will automatically protect the amplifier. The IGM circuit senses the short circuit as an extremely stressfull load condition and attenuates the signal, protecting the channels output transistors from over current stress. If the short circuit remains, the load will be disconnected by the thermal protection circuitry (output relay opens).
SPECIFICATIONS MX 6000
1 kHz, 0.01% THD+N
8ohm Stereo Power = 600W
4ohm Stereo Power = 900W
2ohm Stereo Power = 1000W
8ohm Bridged Mono Power = 1800W
20Hz-20kHz, 0.1% THD+N
8ohm Stereo Power = 550W
4ohm Stereo Power = 800W
2ohm Stereo Power = 900W
8ohm Bridged Mono Power = 1600W
Max RMS Output Voltage (each channel) = 82V
Max Peak Output Voltage = 116V
Frequency Response (+o/-0.3dB, 1W/8ohm) = 20Hz-20kHz, -3dB@135kHz
Power Bandwidth (rated power @ 4ohm,1%THD+N = 20Hz-20kHz,-.84dB/+0dB
TourClass Protection = ACL,IMG, AutoRamp, Short Circuit, DC Voltage turn on/off transient, current inrush, sub/ultrasonic input
THD+N rated power 4ohm/1kHz = < 0.01%
SMPTE IMD (rated power. 8ohm.60Hz &7kHz = < 0.01%
Damping Factor (10-400Hz @ 8ohm = 700:1
Input CMRR (1 kHz) = > -60dB
Standart Voltage Gain (rated power @ 8ohm)‡ = 0.775V
Standart Input Sensitivity (rated power @ 8ohm)‡ = X86.5
Input Impedance (balanced/unbalanced) = > 20kohm/ >10kohm
Hum & Noise ('A' weighted, full power @ 4ohm) = -105 dB
Crosstalk ('A' weighted, full power @ 4ohm) = > -60 dB
Class = H
Input Connectors (per channel) = Female XLR (pin2+, configurable for pin3+) TRS (tip+)
Output Connectors (per channel) = 5-Way binding posts (2pair on CA18) or Speakon Connectors (market dependent)
Filter Storage = 80,000 µ F
Power Supply (factory configured) = 100V - 240V, 50-60Hz
Idle Current Draw (120V) = 2.0A
1/8 Power Curr.Draw (typical music cond., 120V/4ohm) = 8.6A
1/3 Power Curr.Draw (cont.music cond., 120V/4ohm) = 16.0A
Max Curr. Draw (continious music cond., 120V/4ohm) = 21.0A
Thermal Emissions (1/8 Power, 4ohm) = 3250 BTU/hr
Thermal Emissions (1/3 Power, 4ohm) = 4341 BTU/hr
Cooling = Two panel variable speed DC fans, filters detachable without tools
Controls = Front Panel: 2 attenuators, magnetic circuit breaker/power switch Rear Panel: signal ground lift & mode switches; CA18 XLR Polarity & input sens. Voltage Gain Switches
LED Indicators (per channel) = Clip/Limit Signal Temp/DC Active
Construction = Steel Chasis 16 Gauge Double Thickness in rear areas
Dimensions (height x width x depth to rear rack ears) = 3.5'' x 19'' x 18'' 89 x 483 x 457 mm
Gross Weight = 52 lbs 23.60kg
Net Weight = 47 lbs 21.33kg
Warranty = 3 Years
PLA MX8000 Amplifier
Introduction:
MX Series amplifiers are designed for high operating efficiency and accurate sonic performance across the full audio bandwith, even under stressful conditions. In order to maintain quality assurance standards, all MX series amplifiers are built in MASS's state of the art manufacturing facility. Internal components are the finest available, and key sub-assemblies are pre tested before final assembly. Finally, each amplifier is burned in and throughly tested (using precision audio test equipment) before packing. In addition, all MX series amplifiers incorporate MASS exclusive TourClass protection features to safeguard both internal circuitry and connected loudspeakers. This proven combination of advanced design, quality construction, and comprehensive circuit protection is the guarantee of fail safe releability. You can depend on consistent, stable performance even when your MX series amplifier is subjected to punishing extremes in the most demanding fixed or mobile sound reinforcement applications.
Tour Class Protection:
Every model in the MX Series incorporates TourClass protection features.
ACL (Active Clip Limiting):
At the amplifiers full power limit, or clipping point, ACL will be activated. This is indicated by illumination of the Clip LED. The channel gain is automatically reduced, protecting the loudspeakers from potential damage from the high power, continous square waves that would otherwise be produced. ACL may be activated by uncontrolled feedback, oscillations, improper equipment gain settings, or an equipment malfunction upstream from the amplifier. Only steady or excessive cliping (not normal program transients) will trigger ACL. The circuit is virtually transparent in operation and full signal bandwith in maintained.
IGM Impedance Sensing:
IGM (Instantaneous Gain Modulation) is an innovative circuit that allows the maplifier to operate safely into loads as low as 2 ohms. When the amplifier sees a load that overstresses the output stage, the IGM circuit adjust the channel gain to a safe level. Like ACL, the IGM circuit is in audible in normal use. In addition, if extreme and sustained low impedance is encounteredi the amplifiers output relay will open.
ShortCircuit:
If an output is shorted (i.e., defective speakers or crossed speaker wires) the IGM and thermal circuits will automatically protect the amplifier. The IGM circuit senses the short circuit as an extremely stressfull load condition and attenuates the signal, protecting the channels output transistors from over current stress. If the short circuit remains, the load will be disconnected by the thermal protection circuitry (output relay opens).
SPECIFICATIONS MX 8000
1 kHz, 0.01% THD+N
8ohm Stereo Power = 700W
4ohm Stereo Power = 1200W
2ohm Stereo Power = 1400W
8ohm Bridged Mono Power = 2400W
20Hz-20kHz, 0.1% THD+N
8ohm Stereo Power = 650W
4ohm Stereo Power = 1100W
2ohm Stereo Power = 1100W
8ohm Bridged Mono Power = 2400W
Max RMS Output Voltage (each channel) = 90V
Max Peak Output Voltage = 126V
Frequency Response (+o/-0.3dB, 1W/8ohm) = 20Hz-20kHz, -3dB@135kHz
Power Bandwidth (rated power @ 4ohm,1%THD+N = 20Hz-20kHz,-.23dB/+.85dB
TourClass Protection = ACL,IMG, AutoRamp, Short Circuit, DC Voltage turn on/off transient, current inrush, sub/ultrasonic input
THD+N rated power 4ohm/1kHz = < 0.01%
SMPTE IMD (rated power. 8ohm.60Hz &7kHz = < 0.01%
Damping Factor (10-400Hz @ 8ohm = 800:1
Input CMRR (1 kHz) = > -60dB
Standart Voltage Gain (rated power @ 8ohm)‡ = 0.775V
Standart Input Sensitivity (rated power @ 8ohm)‡ = X97.5
Input Impedance (balanced/unbalanced) = > 20kohm/ >10kohm
Hum & Noise ('A' weighted, full power @ 4ohm) = -105 dB
Crosstalk ('A' weighted, full power @ 4ohm) = > -60 dB
Class = H
Input Connectors (per channel) = Female XLR (pin2+, configurable for pin3+) TRS (tip+)
Output Connectors (per channel) = 5-Way binding posts (2pair on CA18) or
Speakon Connectors (market dependent) Filter Storage = 140,000 µ F
Power Supply (factory configured) = 100V - 240V, 50-60Hz
Idle Current Draw (120V) = 2.8A
1/8 Power Curr.Draw (typical music cond., 120V/4ohm) = 10.5A
1/3 Power Curr.Draw (cont.music cond., 120V/4ohm) = 23.0A
Max Curr. Draw (continious music cond., 120V/4ohm) = 30.0A
Thermal Emissions (1/8 Power, 4ohm) = 4750 BTU/hr
Thermal Emissions (1/3 Power, 4ohm) = 6300 BTU/hr
Cooling = Two panel variable speed DC fans, filters detachable without tools
Controls = Front Panel: 2 attenuators, magnetic circuit breaker/power switch Rear Panel: signal ground lift & mode switches; CA18 XLR Polarity & input sens. Voltage Gain Switches
LED Indicators (per channel) = Clip/Limit Signal Temp/DC Active
Construction = Steel Chasis 16 Gauge Double Thickness in rear areas
Dimensions (height x width x depth to rear rack ears) = 3.5'' x 19'' x 18'' 89 x 483 x 457 mm
Gross Weight = 72 lbs 32.68kg
Net Weight = 47 lbs 30.42kg
Warranty = 3 Years
PLA MX10000 Amplifier
Introduction:
MX Series amplifiers are designed for high operating efficiency and accurate sonic performance across the full audio bandwith, even under stressful conditions. In order to maintain quality assurance standards, all MX series amplifiers are built in MASS's state of the art manufacturing facility. Internal components are the finest available, and key sub-assemblies are pre tested before final assembly. Finally, each amplifier is burned in and throughly tested (using precision audio test equipment) before packing. In addition, all MX series amplifiers incorporate MASS exclusive TourClass protection features to safeguard both internal circuitry and connected loudspeakers. This proven combination of advanced design, quality construction, and comprehensive circuit protection is the guarantee of fail safe releability. You can depend on consistent, stable performance even when your MX series amplifier is subjected to punishing extremes in the most demanding fixed or mobile sound reinforcement applications.
Tour Class Protection:
Every model in the MX Series incorporates TourClass protection features.
ACL (Active Clip Limiting):
At the amplifiers full power limit, or clipping point, ACL will be activated. This is indicated by illumination of the Clip LED. The channel gain is automatically reduced, protecting the loudspeakers from potential damage from the high power, continous square waves that would otherwise be produced. ACL may be activated by uncontrolled feedback, oscillations, improper equipment gain settings, or an equipment malfunction upstream from the amplifier. Only steady or excessive cliping (not normal program transients) will trigger ACL. The circuit is virtually transparent in operation and full signal bandwith in maintained.
IGM Impedance Sensing:
IGM (Instantaneous Gain Modulation) is an innovative circuit that allows the maplifier to operate safely into loads as low as 2 ohms. When the amplifier sees a load that overstresses the output stage, the IGM circuit adjust the channel gain to a safe level. Like ACL, the IGM circuit is in audible in normal use. In addition, if extreme and sustained low impedance is encounteredi the amplifiers output relay will open.
ShortCircuit:
If an output is shorted (i.e., defective speakers or crossed speaker wires) the IGM and thermal circuits will automatically protect the amplifier. The IGM circuit senses the short circuit as an extremely stressfull load condition and attenuates the signal, protecting the channels output transistors from over current stress. If the short circuit remains, the load will be disconnected by the thermal protection circuitry (output relay opens).
SPECIFICATIONS MX 10000
1 kHz, 0.01% THD+N
8ohm Stereo Power = 1000W
4ohm Stereo Power = 1800W
2ohm Stereo Power = 2500W
8ohm Bridged Mono Power = 3600W
20Hz-20kHz, 0.1% THD+N
8ohm Stereo Power = 950W
4ohm Stereo Power = 1700W
2ohm Stereo Power = 2400W
8ohm Bridged Mono Power = 3400W
RMS Output Voltage (each channel) = 90V
Max Peak Output Voltage = 140V
Frequency Response (+o/-0.3dB, 1W/8ohm) = 20Hz-20kHz, -3dB@150kHz
Power Bandwidth (rated power @ 4ohm,1%THD+N = 20Hz-20kHz,-.2dB/+.2dB
TourClass Protection = ACL,IMG, AutoRamp, Short Circuit, DC Voltage turn on/off transient, current inrush, sub/ultrasonic input
THD+N rated power 4ohm/1kHz = < 0.03%
SMPTE IMD (rated power. 8ohm.60Hz &7kHz = < 0.01%
Damping Factor (10-400Hz @ 8ohm = 800:1
Input CMRR (1 kHz) = > -70dB
Standart Voltage Gain (rated power @ 8ohm)‡ = 0.775V
Standart Input Sensitivity (rated power @ 8ohm)‡ = X115
Input Impedance (balanced/unbalanced) = > 20kohm/ >10kohm
Hum & Noise ('A' weighted, full power @ 4ohm) = -115 dB
Crosstalk ('A' weighted, full power @ 4ohm) = > -80 dB
Class = H
Input Connectors (per channel) = Female XLR (pin2+, configurable for pin3+) TRS (tip+)
Output Connectors (per channel) = 5-Way binding posts (2pair on CA18) or Speakon Connectors (market dependent)
Filter Storage = 144,000 µ F
Power Supply (factory configured) = 100V - 240V, 50-60Hz
Idle Current Draw (120V) = 3.0A
1/8 Power Curr.Draw (typical music cond., 120V/4ohm) = 12.0A
1/3 Power Curr.Draw (cont.music cond., 120V/4ohm) = 25.0A
Max Curr. Draw (continious music cond., 120V/4ohm) = 36.0A
Thermal Emissions (1/8 Power, 4ohm) = 7125 BTU/hr
Thermal Emissions (1/3 Power, 4ohm) = 9450 BTU/hr
Cooling = Two panel variable speed DC fans, filters detachable without tools
Controls = Front Panel: 2 attenuators, magnetic circuit breaker/power switch Rear Panel: signal ground lift & mode switches; CA18 XLR Polarity & input sens. Voltage Gain Switches
LED Indicators (per channel) = Clip/Limit Signal Temp/DC Active
Construction = Steel Chasis 16 Gauge Double Thickness in rear areas
Dimensions (height x width x depth to rear rack ears) = 3.5'' x 19'' x 18'' 89 x 483 x 457 mm
Gross Weight = 82 lbs 37.23kg
Net Weight = 77 lbs 34.96kg
Warranty = 3 Years
The PLASUB is a self power sub-bass speaker. Desingned to wide variety of venues at high SPL. Ideal macth of Line-8 Line Array speakers. The PLASUB's power and bandwitdh handle high continuous operating levels and extreme transient information with minimal distotion in its operating frequency range.
Operation Range = 30hz - 150hz
Sensivity(1Watt/1m) = 139dB
Coverage = 360° (single unit); varies with number of units and configuration
Transducer = 2x18" Cone drivers 1200 Watts RMS
Audio Input Type = Differential, electronically balanced
Maximum Common Mode Range = ±15 V DC, clamped to earth for voltage transient protection
Connectors = Female XLR input with male XLR loop
Input Impedance = 10 kOhm differential between pins 2 and 3
Wiring = Pin 1: Chassis/earth through 220 k?, 1000 pF, 15 V clamp network to, provide virtual ground lift at audio?frequencies?, Pin 2: Signal +?, Pin 3: Signal -?, Case: Earth ground and chassis
DC Blocking = None on input, DC blocked through signal processing
CMRR = >50 dB, typically 80 dB (50 Hz–500 Hz)
RF Filter = Common mode: 425 kHz
TIM Filter = Integral sinyal processing (<80 kHz)
Nominal Input Sensitivity = 0 dBV (1 V rms, 1.4 V pk) continuous is typically the onset of limiting for noise and music
Input Level = Audio source must be capable of producing a minimum of +20 dBV (10 V rms, 14 V pk) into 600 ohm in order to produce maximum peak SPL over the operating bandwidth of the loudspeaker
Amplifiers Type = Two-channel complementary power MOSFET output stages (class AB/H)
Output Power = 2250 W (1125 W/channel)
THD, IM, TIM = <.02%
Load Capacity = 4 ohm each channel
Cooling = Forced air cooling, two fans (one ultrahigh-speed reserve fan)
AC Power Connector = 250 V AC NEMA L6-20 (twist lock), IEC 309 male inlet, or VEAM
Automatic Voltage Selection = Automatic, two ranges, each with high-low voltage tap
Safety Agency Rated Operating Range = 95 V AC – 125 V AC, 208 V AC - 235 V AC; 50/60 Hz
Turn-on and Turn-off Points = 85 V AC - 134 V AC; 165 V AC - 264 V AC; 50/60 Hz
Current Draw: Idle Current: = 0.640 A rms (115 V AC); 0.320 A rms (230 V AC); 0.850 A rms (100 V AC)
Max Long-Term Continuous Current (>10 sec) = 8.8 A rms (115 V AC); 4 A rms (230 V AC); 10 A rms (100 V AC)
Burst Current (<1 sec) = 19 A rms (115 V AC); 9.5 A rms (230 V AC); 22 A rms (100 V AC)
The PLA Line-8 is a full-range bi-amped line source array speaker. Desingned to wide variety of venues at high SPL.
Operation Range = 70hz - 18khz
Sensivity(1Watt/1m) Low Freq = 99dB
High Freg = 104dB
Horizontal Coverage = 120°
Vertical Coverage = Defined by height and configuration of the array
Power Handling Low freq = 550 Watt RMS
High Freq = 80 Waat RMS
Max SPL 1 Meter Low Freq = 126dB Cont. / 132dB Peak
High Freq = 122dB Cont. / 128dB Peak
Reommented Amp (3 Line 2813)
Low Freq = 1800 Watt
High Freq = 150 Watt
Nominal Impedance Low Freq = 16 Ohm
High Freq = 8 Ohm
Crossover Frequency = DSP Settings
Transducer Low Freq = 2x8" Woofer
High Freq = 1x1,3" Custom made driver
Enclosure = 18ply Fin Birch
Input = NL4 x 2
Dimensions = 25,3cm H (ön) (rigsiz.22,5cm) | 14,8cm H (geri) (rigsiz. is 16,6cm) | 75,1cm W (rigsiz. 70,6cm) | 57,2cm D (rigsiz. 44,8cm)
The PLA12 stage monitor comprises a 12-inch low-frequency cone driver, a 1.4-inch driver. The PLA12 excels in applications that require efficient response to 70 Hz for clean, high-level reproduction of bass and drums.
Operation Range = 70hz - 18khz
Sensivity(1Watt/1m) = 111dB
SPL(1Watt/1m) = 138dB
RMS = 400 Watt
Program = 600 Watt
Coverage = 45° x 45°
Transducer
Low Driver = 12" custom
High Driver = 1.4" Bnc
Connectors = 2xNeutrik NL4 Speakon
Dimensions = 57 cm H 36,8 cm W 35,6 cm D
The PLA1514 excels in applications that require efficient response to 70 Hz for clean, high-level reproduction of small PA aplications and side/back fill.
The PLA15 full-range speaker comprises a 15-inch low-frequency cone driver, a 3-inch diaphragm compression driver. The PLA15 excels in applications that require efficient response to 70 Hz for clean, high-level reproduction of small PA aplications and side/back fill.
Operation Range = 70hz - 18khz
Sensivity(1Watt/1m) = 110dB
SPL(1Watt/1m) = 138dB
RMS = 400 Watt
Program = 600 Watt
Coverage = 45° x 45°
Transducer
Low Driver = 15" custom
High Driver = 1.4" Bnc
Connectors = 2xNeutrik NL4 Speakon
Dimensions = 78,8cm H 49cm W (front) 24,7cm W (back) 48,3cm D
|
|
